Williams AH030W2B402L00
Williams AH030W2B402L00
Hover to zoom
1 Of 5

Williams 'B' Series Belt-Drive Horizontal Air Handler, Left Piping, 208V, 4 Coil Rows (CW or HW) - 3,000 CFM, 281,413 BTU

Model:

AH030W2B402L00

Write A Review
Product Discontinued
Sorry, this product is no longer available.
Continue Shopping With These Categories
Williams 'B' Series Belt-Drive Horizontal Air Handler, Left Piping, 208V, 4 Coil Rows (CW or HW) - 3,000 CFM, 281,413 BTU
Williams 'B' Series Belt-Drive Horizontal Air Handler, Left Piping, 208V, 4 Coil Rows (CW or HW) - 3,000 CFM, 281,413 BTU
Model: AH030W2B402L00
Product Discontinued
Accessories
Features
Specifications
Reviews
How-To Articles
Manuals
Share

Recommended Accessories

eComfort expert image
Expert Recommended Accessories Selected by Ken, our Expert
Required Accessories 9
These accessories are required to properly setup/install this product.
Optional Accessories 10

Features

    A Horizontal model of Belt-Driven Air Handlers for both hydronic and DX applications, these rugged units are dependable air handlers. Housed in a heavy-gauge, galvanized steel cabinet. Controls and motors are factory-mounted and provided in a single-point power supply. Access doors are provided on both sides of the unit for easy maintenance.
  • Williams B302402L00 Features
  • Heavy-gauge galvanized steel cabinet insulated with 1/2" thick, over three-pound density, neoprene-coated fiberglass.
  • Two-pipe or Four-pipe hydronic heating and/or cooling. Four pipe systems may be converted to a two-pipe system by capping off one set of pipes.
  • Coils are 1/2" OD copper tubes with aluminum fins (10 FPI) equipped with manual-air vent. Coils are 100% underwater pressure tested at 350 PSI with a 300 PSI working pressure.
  • Galvanized drain pan features powder-coated epoxy with 1/4" thick elastomeric insulation and has primary and secondary drain connections.
  • Belt-driven, draw-through design with forward-curved and dynamically balanced blowers.
  • Wide range of motor sizes and adjustable, variable-pitch drive sheave and cast-iron pulley keyed to motor shaft (ordered separately & required for operation).
  • Two-inch thick, 30/30 pleated filter, flatly mounted, with spring-loaded clips on each side of the access door for easy maintenance without the use of tools.
  • Product Note
    Williams B302402L00 Compatible Sheave Kits:
      Kit Model # at Horsepower @ Inches of Static Pressure

    • S63 operating at 3/4 hp @ 0.0
    • S10/S27* operating at 1 hp @ 0.1
    • S11/S26* operating at 1 hp @ 0.2
    • S11/S26* operating at 1 hp @ 0.3
    • S12/S25* operating at 1 hp @ 0.4
    • S12/S25* operating at 1-1/2 hp @ 0.5
    • S6/S17* operating at 1-1/2 hp @ 0.6
    • S6/S17* operating at 1-1/2 hp @ 0.7
    • S7/S16* operating at 1-1/2 hp @ 0.8
    • S7/S16* operating at 1-1/2 hp @ 0.9
    • S7/S16* operating at 1-1/2 hp @ 1.0

    • * Use with 3-phase motors only
California residents see
Warning: This product can expose you to chemicals including Epichlorohydrin which is known to the State of California to cause Cancer.
For more information go to: www.p65Warnings.ca.gov

Specifications

AH030W2B402L00
specs product image PID-43763
General Information
Product Line
B
Blower Motor Type
Variable Speed
Coil Type
Hydronic
Configuration Learn More
Configuration
Orientation describes the direction that air will flow through a piece of equipment. (e.g. air will flow horizontally through a "Horizontal" unit heater.) Most equipment will only function properly if installed in the proper orientation.
Horizontal
Electric Heat
Optional
Additional Model Numbers

B302402L00, AH030W2B402L00

Performance
Heating BTU
281413
Nominal Maximum Cooling Capacity
74163 BTU
Maximum Air Flow
3000 CFM
Electrical Data
Voltage
208 Volts
Phase
1
Frequency
60 Hz
Dimensions
Cold Water Inlet
1 1/4 Inches
Hot Water Outlet
1 1/4 Inches
Hot Water Inlet
1 1/4 Inches
Cold Water Outlet
1 1/4 Inches
Product Height
30 Inches
Product Width
47 Inches
Product Depth
48 Inches
Product Weight
440 Pounds
Shipping Weight
450 Pounds
Warranty Information
Parts Warranty Learn More
Parts Warranty
A warranty is a safeguard from defects in manufacturing and can vary in length and terms. Some manufacturers require registration for extended warranty benefits, be sure to check out features and the warranty document. To see the manufacturer's warranty statement, click on the Manuals tab. Learn More
1 Year

Reviews

Williams AH030W2B402L00 Reviews & Ratings
Be the First to Write a Review
Do you own this product?
Please share your insights with fellow shoppers.

How-To Articles

Hydronic System Accessory Guide
Hydronic System Accessory Guide
How warm does a coat keep you without gloves and a hat? Accessories are sometim...
Replacing HVAC equipment after a flood
Replacing HVAC equipment after a flood
"Water got into my furnace!" It's a complaint I hear all too often when people ...
How to Pick the Perfect Hot Water Towel Warmer
How to Pick the Perfect Hot Water Towel Warmer
Hydronic towel warmers are a great way to take advantage of your existing hot w...
eComfort How-To Library
eComfort How-To Library
Articles, Tips and Buying Guides from Our Experts

Manuals

 
Media Gallery
Williams 'B' Series Belt-Drive Horizontal Air Handler, Left Piping, 208V, 4 Coil Rows (CW or HW) - 3,000 CFM, 281,413 BTU
Williams AH030W2B402L00
Customer Review Images